Is it possible to power a microcontroller via inductance from an AC power line?
I have an AC mains wire powering a pump running at 220V at 5-10A. Is it possible to wind a secondary wire around the outside of the insulation of one of the two "hot" wires (single-phase) to get low-voltage AC that could be rectified to DC and used to power a microcontroller?
The goal is to monitor current while the pump is in use, using a separate split-core transformer as an analog input, and report usage via Wifi or Zigbee without requiring a separate DC power supply.
transformer inductance
asked 3 hours ago
Henry G
283
add a comment |
I have an AC mains wire powering a pump running at 220V at 5-10A. Is it possible to wind a secondary wire around the outside of the insulation of one of the two "hot" wires (single-phase) to get low-voltage AC that could be rectified to DC and used to power a microcontroller?
The goal is to monitor current while the pump is in use, using a separate split-core transformer as an analog input, and report usage via Wifi or Zigbee without requiring a separate DC power supply.
transformer inductance
asked 3 hours ago
Henry G
283
that is what a transformer does
– analogsystemsrf
2 hours ago
add a comment |
I have an AC mains wire powering a pump running at 220V at 5-10A. Is it possible to wind a secondary wire around the outside of the insulation of one of the two "hot" wires (single-phase) to get low-voltage AC that could be rectified to DC and used to power a microcontroller?
The goal is to monitor current while the pump is in use, using a separate split-core transformer as an analog input, and report usage via Wifi or Zigbee without requiring a separate DC power supply.
transformer inductance
asked 3 hours ago
Henry G
283
I have an AC mains wire powering a pump running at 220V at 5-10A. Is it possible to wind a secondary wire around the outside of the insulation of one of the two "hot" wires (single-phase) to get low-voltage AC that could be rectified to DC and used to power a microcontroller?
The goal is to monitor current while the pump is in use, using a separate split-core transformer as an analog input, and report usage via Wifi or Zigbee without requiring a separate DC power supply.
transformer inductance
transformer inductance
asked 3 hours ago
Henry G
283
asked 3 hours ago
Henry G
283
asked 3 hours ago
Henry G
283
asked 3 hours ago
Henry G
283
asked 3 hours ago
Henry G
283
283
that is what a transformer does
– analogsystemsrf
2 hours ago
add a comment |
that is what a transformer does
– analogsystemsrf
2 hours ago
that is what a transformer does
– analogsystemsrf
2 hours ago
that is what a transformer does
– analogsystemsrf
2 hours ago
add a comment |
1 Answer
1
active
oldest
votes
No, the wire will not radiate a magnetic field along the lengt of the wire but straight out of the wire. To make a transformer and extract energy you need an magnetic field that alternates. As you will have a split core to measure the current the best idea would be to use it to both measure the current and extract power to your circuit. This only works with a real current transformer and not with a modern Hall effect variant, if you need the Hall effect model for accuracy in your measurements you will need a separate split core current transformer to power your circuit.
The resultant circuit is much like an transformer with only one turn of primary winding, the current in the secondary winding will be the current in the AC wire divided by the number of turns in the current transformers winding. Note that the circuit outputs a current and if the load is not sufficient the voltage can be quite high, therefor you need to be sure to load the current transformer and to have a over voltage protection that can handle the excess power, especially in events of high current on the AC line, like starting currents of an electrical motor.
If you then put a resistor or other current sensing element in series of the output of your current transformer that measures the total current you can know the current trough the AC line at the same time as you uses it to power your current sensing circuit.
answered 2 hours ago
RobinSt
864
A voltage is induced, not a current. If the secondary is open-circuit, there will be zero current.
– Chu
42 mins ago
Searching for current transformers revealed that 1. they're apparently mostly used for current sensing and metering, sometimes in large substations and 2. off the shelf CTs can be rather expensive. I'm also wondering if a Rogowski coil might work better for this purpose (collecting enough current to rectify and run a low-power DC circuit with a microcontroller).
– Henry G
14 mins ago
add a comment |
Your Answer
StackExchange.ifUsing("editor", function () {
return StackExchange.using("mathjaxEditing", function () {
StackExchange.MarkdownEditor.creationCallbacks.add(function (editor, postfix) {
StackExchange.mathjaxEditing.prepareWmdForMathJax(editor, postfix, [["\$", "\$"]]);
});
});
}, "mathjax-editing");
StackExchange.ifUsing("editor", function () {
return StackExchange.using("schematics", function () {
StackExchange.schematics.init();
});
}, "cicuitlab");
StackExchange.ready(function() {
var channelOptions = {
tags: "".split(" "),
id: "135"
};
initTagRenderer("".split(" "), "".split(" "), channelOptions);
StackExchange.using("externalEditor", function() {
// Have to fire editor after snippets, if snippets enabled
if (StackExchange.settings.snippets.snippetsEnabled) {
StackExchange.using("snippets", function() {
createEditor();
});
}
else {
createEditor();
}
});
function createEditor() {
StackExchange.prepareEditor({
heartbeatType: 'answer',
autoActivateHeartbeat: false,
convertImagesToLinks: false,
noModals: true,
showLowRepImageUploadWarning: true,
reputationToPostImages: null,
bindNavPrevention: true,
postfix: "",
imageUploader: {
brandingHtml: "Powered by u003ca class="icon-imgur-white" href="https://imgur.com/"u003eu003c/au003e",
contentPolicyHtml: "User contributions licensed under u003ca href="https://creativecommons.org/licenses/by-sa/3.0/"u003ecc by-sa 3.0 with attribution requiredu003c/au003e u003ca href="https://stackoverflow.com/legal/content-policy"u003e(content policy)u003c/au003e",
allowUrls: true
},
onDemand: true,
discardSelector: ".discard-answer"
,immediatelyShowMarkdownHelp:true
});
}
});
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function () {
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2felectronics.stackexchange.com%2fquestions%2f414159%2fis-it-possible-to-power-a-microcontroller-via-inductance-from-an-ac-power-line%23new-answer', 'question_page');
}
);
Post as a guest
Required, but never shown
1 Answer
1
active
oldest
votes
1 Answer
1
active
oldest
votes
active
oldest
votes
active
oldest
votes
No, the wire will not radiate a magnetic field along the lengt of the wire but straight out of the wire. To make a transformer and extract energy you need an magnetic field that alternates. As you will have a split core to measure the current the best idea would be to use it to both measure the current and extract power to your circuit. This only works with a real current transformer and not with a modern Hall effect variant, if you need the Hall effect model for accuracy in your measurements you will need a separate split core current transformer to power your circuit.
The resultant circuit is much like an transformer with only one turn of primary winding, the current in the secondary winding will be the current in the AC wire divided by the number of turns in the current transformers winding. Note that the circuit outputs a current and if the load is not sufficient the voltage can be quite high, therefor you need to be sure to load the current transformer and to have a over voltage protection that can handle the excess power, especially in events of high current on the AC line, like starting currents of an electrical motor.
If you then put a resistor or other current sensing element in series of the output of your current transformer that measures the total current you can know the current trough the AC line at the same time as you uses it to power your current sensing circuit.
answered 2 hours ago
RobinSt
864
A voltage is induced, not a current. If the secondary is open-circuit, there will be zero current.
– Chu
42 mins ago
Searching for current transformers revealed that 1. they're apparently mostly used for current sensing and metering, sometimes in large substations and 2. off the shelf CTs can be rather expensive. I'm also wondering if a Rogowski coil might work better for this purpose (collecting enough current to rectify and run a low-power DC circuit with a microcontroller).
– Henry G
14 mins ago
add a comment |
No, the wire will not radiate a magnetic field along the lengt of the wire but straight out of the wire. To make a transformer and extract energy you need an magnetic field that alternates. As you will have a split core to measure the current the best idea would be to use it to both measure the current and extract power to your circuit. This only works with a real current transformer and not with a modern Hall effect variant, if you need the Hall effect model for accuracy in your measurements you will need a separate split core current transformer to power your circuit.
The resultant circuit is much like an transformer with only one turn of primary winding, the current in the secondary winding will be the current in the AC wire divided by the number of turns in the current transformers winding. Note that the circuit outputs a current and if the load is not sufficient the voltage can be quite high, therefor you need to be sure to load the current transformer and to have a over voltage protection that can handle the excess power, especially in events of high current on the AC line, like starting currents of an electrical motor.
If you then put a resistor or other current sensing element in series of the output of your current transformer that measures the total current you can know the current trough the AC line at the same time as you uses it to power your current sensing circuit.
answered 2 hours ago
RobinSt
864
A voltage is induced, not a current. If the secondary is open-circuit, there will be zero current.
– Chu
42 mins ago
Searching for current transformers revealed that 1. they're apparently mostly used for current sensing and metering, sometimes in large substations and 2. off the shelf CTs can be rather expensive. I'm also wondering if a Rogowski coil might work better for this purpose (collecting enough current to rectify and run a low-power DC circuit with a microcontroller).
– Henry G
14 mins ago
add a comment |
No, the wire will not radiate a magnetic field along the lengt of the wire but straight out of the wire. To make a transformer and extract energy you need an magnetic field that alternates. As you will have a split core to measure the current the best idea would be to use it to both measure the current and extract power to your circuit. This only works with a real current transformer and not with a modern Hall effect variant, if you need the Hall effect model for accuracy in your measurements you will need a separate split core current transformer to power your circuit.
The resultant circuit is much like an transformer with only one turn of primary winding, the current in the secondary winding will be the current in the AC wire divided by the number of turns in the current transformers winding. Note that the circuit outputs a current and if the load is not sufficient the voltage can be quite high, therefor you need to be sure to load the current transformer and to have a over voltage protection that can handle the excess power, especially in events of high current on the AC line, like starting currents of an electrical motor.
If you then put a resistor or other current sensing element in series of the output of your current transformer that measures the total current you can know the current trough the AC line at the same time as you uses it to power your current sensing circuit.
answered 2 hours ago
RobinSt
864
No, the wire will not radiate a magnetic field along the lengt of the wire but straight out of the wire. To make a transformer and extract energy you need an magnetic field that alternates. As you will have a split core to measure the current the best idea would be to use it to both measure the current and extract power to your circuit. This only works with a real current transformer and not with a modern Hall effect variant, if you need the Hall effect model for accuracy in your measurements you will need a separate split core current transformer to power your circuit.
The resultant circuit is much like an transformer with only one turn of primary winding, the current in the secondary winding will be the current in the AC wire divided by the number of turns in the current transformers winding. Note that the circuit outputs a current and if the load is not sufficient the voltage can be quite high, therefor you need to be sure to load the current transformer and to have a over voltage protection that can handle the excess power, especially in events of high current on the AC line, like starting currents of an electrical motor.
If you then put a resistor or other current sensing element in series of the output of your current transformer that measures the total current you can know the current trough the AC line at the same time as you uses it to power your current sensing circuit.
answered 2 hours ago
RobinSt
864
answered 2 hours ago
RobinSt
864
answered 2 hours ago
RobinSt
864
answered 2 hours ago
RobinSt
864
864
A voltage is induced, not a current. If the secondary is open-circuit, there will be zero current.
– Chu
42 mins ago
Searching for current transformers revealed that 1. they're apparently mostly used for current sensing and metering, sometimes in large substations and 2. off the shelf CTs can be rather expensive. I'm also wondering if a Rogowski coil might work better for this purpose (collecting enough current to rectify and run a low-power DC circuit with a microcontroller).
– Henry G
14 mins ago
add a comment |
A voltage is induced, not a current. If the secondary is open-circuit, there will be zero current.
– Chu
42 mins ago
Searching for current transformers revealed that 1. they're apparently mostly used for current sensing and metering, sometimes in large substations and 2. off the shelf CTs can be rather expensive. I'm also wondering if a Rogowski coil might work better for this purpose (collecting enough current to rectify and run a low-power DC circuit with a microcontroller).
– Henry G
14 mins ago
A voltage is induced, not a current. If the secondary is open-circuit, there will be zero current.
– Chu
42 mins ago
A voltage is induced, not a current. If the secondary is open-circuit, there will be zero current.
– Chu
42 mins ago
Searching for current transformers revealed that 1. they're apparently mostly used for current sensing and metering, sometimes in large substations and 2. off the shelf CTs can be rather expensive. I'm also wondering if a Rogowski coil might work better for this purpose (collecting enough current to rectify and run a low-power DC circuit with a microcontroller).
– Henry G
14 mins ago
Searching for current transformers revealed that 1. they're apparently mostly used for current sensing and metering, sometimes in large substations and 2. off the shelf CTs can be rather expensive. I'm also wondering if a Rogowski coil might work better for this purpose (collecting enough current to rectify and run a low-power DC circuit with a microcontroller).
– Henry G
14 mins ago
add a comment |
Thanks for contributing an answer to Electrical Engineering Stack Exchange!
- Please be sure to answer the question. Provide details and share your research!
But avoid …
- Asking for help, clarification, or responding to other answers.
- Making statements based on opinion; back them up with references or personal experience.
Use MathJax to format equations. MathJax reference.
To learn more, see our tips on writing great answers.
Some of your past answers have not been well-received, and you're in danger of being blocked from answering.
Please pay close attention to the following guidance:
- Please be sure to answer the question. Provide details and share your research!
But avoid …
- Asking for help, clarification, or responding to other answers.
- Making statements based on opinion; back them up with references or personal experience.
To learn more, see our tips on writing great answers.
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function () {
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2felectronics.stackexchange.com%2fquestions%2f414159%2fis-it-possible-to-power-a-microcontroller-via-inductance-from-an-ac-power-line%23new-answer', 'question_page');
}
);
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
that is what a transformer does
– analogsystemsrf
2 hours ago